1783-ETAP2F 工业以太网网络组件

Allen-Bradley ETAP2F是一种工业以太网网络组件，具有一(1)个铜质端口和两(2)个光纤接口，支持10/100 Mbps通信速度。它也可用于encompass合作伙伴模块以及非Allen-Bradley和第三方产品。

1783-ETAP2F的单铜端口支持10/100 Mbps自动协商功能，支持全双工或半双工模式。1783-ETAP2F的双光纤端口同样能够实现10/100 Mbps的通信速度，支持更长的通信距离，因此对噪声和电气干扰的敏感度更高。

1783-ETAP2F不安装在任何背板上，也不从中吸取电流。它由外部电源供电，输入电压范围为20.4至27.6伏DC，标称输入电压为24伏直流电。该以太网设备可以使用DIN导轨支架安装，也可以直接安装在外壳板上。它能够水平和垂直安装，提供了安装的灵活性。该设备占用最小的面板空间，但是必须遵循特定的安装间隙，以确保正确操作和连接质量。这些间隙包括7.62厘米（3英寸。）的空间和2.54厘米（1英寸。）的空间。对于光缆入口，建议至少5.08厘米或2英寸，以符合光缆的必要弯曲半径。

Allen-Bradley 1783-ETAP2F分路器是一款以太网/IP分路器，具有1个铜缆端口和2个光纤端口。光纤收发器类型为100Base-FX IEEE 802.3u收发器。光学波长为1310纳米。启动时，62.5/125微米光纤中的最小发射机发射功率为-19 dBm，50/125微米光纤中的最小发射机发射功率为-22.5 dBm。和接收器灵敏度水平为-31.8 dBm和-14 dBm。62.5/125微米多模光纤在额定BET下的光纤信道功率预算为12.8 dB，50/125微米多模光纤为9.3 dB。连接器类型为IEC 61754-20 LC连接器，每个连接的插入损耗为0.75 dB。通道长度为2公里。

1783-ETAP2F抽头在24伏DC下的电流消耗为260毫安。DC电压输入的额定值为24伏DC。功耗为6.24瓦，功耗为6.24瓦。1783-ETAP2F抽头的外壳是打开的。1783-ETAP2F水龙头的工作温度范围为-25至60摄氏度，储存温度范围为-40至85摄氏度。相对湿度范围为5至95%。1783-ETAP2F抽头的非运行和运行冲击额定值分别为50 G和30 G。该设备在10至500赫兹时的额定振动为5 G。1783-ETAP2F tap具有排放等级。此外，它的额定空气放电电压为8千伏，接触放电电压为6千伏。1783-ETAP2F tap通过了CE、C-Tick、Ex和KC认证

The Allen-Bradley ETAP2F is an industrial Ethernet networking component that features One (1) Copper Ports and Two (2) Fiber Optic interfaces supporting 10/100 Mbps communication speed. It may also be used with encompass partner modules as well as non-Allen-Bradley and 3rd party products.

The single copper port of the 1783-ETAP2F is capable for 10/100 Mbps with auto-negotiating capability and supports operation in full or half duplex modes. The dual fiber optic ports of the 1783-ETAP2F is similarly capable of 10/100 Mbps communication speed with support for longer communication distance that exhibits increased susceptibility to noise and disturbances of electrical nature.

The 1783-ETAP2F does not install to any backplane nor does not draw current from it. It is supplied externally by a power supply with input voltage range of 20.4…27.6V DC with a nominal input voltage of 24VDC. This Ethernet device can be installed using a DIN rail mount or directly mounted to an enclosure plate. It is capable of horizontal and vertical mounting, providing flexibility of installation. This device occupies minimum panel space however, specific installation clearance must be followed to ensure proper operation and quality of connection. These clearances include 7.62 cm (3 in.) of space on the bottom of the tap and 2.54 cm (1 in.) of space on the remaining sides of the tap. For Fiber cable entry, at least 5.08 cm or 2 inches is recommended to comply with the necessary bending radius of the Fiber Optic cable.

The Allen-Bradley 1783-ETAP2F tap is an Ethernet/IP tap with 1 copper port and 2 fiber ports. The Fiber transceiver type is the 100Base-FX IEEE 802.3u transceiver. The optical wavelength is 1310 nanometers. The minimum transmitter launch power at startup is -19 dBm into 62.5/125 micrometer fiber and -22.5 dBm into 50/125 micrometer fiber. The minimum and maximum receiver sensitivity levels are -31.8 dBm and -14 dBm. The fiber channel power budget at the rated BET is 12.8 dB for 62.5/125 micrometer multimode fiber and 9.3 dB for 50/125 micrometer multimode fiber. The connector type is the IEC 61754-20 LC connector with a maximum insertion loss of 0.75 dB per connection. The maximum channel length is 2 kilometers.

The maximum current consumption for the 1783-ETAP2F tap is 260 milliamps at 24 Volts DC. The rating for the DC voltage input is 24 Volts DC. The maximum power consumption is 6.24 Watts and the maximum power dissipation is 6.24 Watts. The enclosure of the 1783-ETAP2F tap is open. The operating temperature range for the 1783-ETAP2F tap is -25 to 60 degrees Celsius and the storage temperature range is -40 to 85 degrees Celsius. The relative humidity range is 5 to 95%. The non-operating and operating shock ratings for the 1783-ETAP2F tap are 50 G and 30 G, respectively. The vibration rating for the device is 5 G at 10 to 500 Hertz. The 1783-ETAP2F tap has a Class A emissions rating. Furthermore, it is rated for 8 kilovolts of air discharges and 6 kilovolts of contact discharges. The 1783-ETAP2F tap is certified by the CE, C-Tick, Ex, and KC

standards.