体积电阻率、表面电阻率测定仪

Volume resistivity of surface resistivity tester

Digital high resistance, a current measuring instrument type: EST-121: volume resistivity, surface resistivity uses: Instrumentation Test

One, volume resistivity surface resistivity tester overview

This instrument can measure high resistance, and measuring current. The American company In large scale integrated circuit and patented technology, the instrument has the advantages of small volume, light weight, high accuracy. Dual 3.1/2 digital display the resistance high resistance meter and current. Limit from 1× 104 Ω～ 1× 1018 Ω, is currently the most wide measurement range, the most accurate digital ultra high resistance meter. Current measurement range of 2× 10-4 ～ 1× 10-16A. The built-in test voltage is 10/50/100/250/500/1000V adjustable. The instrument has the advantages of high precision, good stability, showing a rapid, easy reading, applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as the resistance value of the test as well as insulating materials electrical and electronic products insulation resistance measurement. The instrument can measure the resistance, and can directly measure the weak current. 

Instrument is fully consistent with and better than the national standard GB1410 " solid electrical insulating materials, insulation resistance, volume resistivity and surface resistance test method " and " American Standard ASTM D257 DC resistance or conductance of insulating materials test methods " and other standards.

Two, volume resistivity surface resistivity tester main features

Resistance measuring range 0.01× 104 Ω～ 1× 1018 Ω

Current measurement range of 2× 10-4A ～ 1× 10-16A

Small volume, light weight, high accuracy

Resistance, current double display

Good performance is stable, easy reading

All the test voltage （ 10/50/100/250/500/1000V ） test resistance results in reading, is removed from the old high resistance meter in different test voltage or different scale should be multiplied by the coefficient of the inconvenient trouble, allowing the measurement of high resistance as the multimeter is used to measure the general resistance of samples is simple.

Not only can measure high resistance and micro current

Wide application: applied to anti-static products such as anti-static shoes, anti-static plastic rubber products, computer room anti-static floor activities such as resistance testing electrical and electronic products insulation resistance measurement

Three, volume resistivity surface resistivity tester technical indicators

The 1 resistor measurement range: 0.01× 104 Ω～ 1× 1018 Ω.

The 2 current measurement range : 2 × 10-4A～ 1 × 10-16A

3 double header display: 3.1/2 LED display

4 built-in test voltage: 10V, 50V, 100V, 250, 500, 1000V

5 basic accuracy: 1% （ note ）

6: use environment temperature: 0℃ ~ 40 ℃, relative humidity <80%

7 built-in test voltage: 10/50/100/250/500/1000V arbitrary switching

The 8 power supply forms: AC 220V, 50HZ, power consumption is about 5W

Four, volume resistivity surface resistivity meter working principle

According to the Ohm's law, the measured resistance is equal to voltage is applied through Rx V divided by the current I. The traditional high resistance meter is the working principle of measuring voltage V fixed, by measuring the current flows through the sampling resistor I to get the value of resistance. From Ohm's law can be seen, because the current I is inversely proportional to the resistance, but not proportional to the resistance, so the display value is nonlinear, namely the resistance to infinity, the current is zero, i.e., zero is∞, in the vicinity of the scale is very dense, with a low resolution. The scale is nonlinear. Because the measurement of different resistance, the voltage V also vary, so the average high resistance meter is poor accuracy, low resolution.

At the same time measure the voltage across the resistor V and the current through the resistor I, through the interior of the large scale integrated circuit to complete the voltage divided by the current calculation, and then the results obtained after A/D conversion to digital show resistance, even if the voltage across the resistor V and the current through the resistor I is changed at the same time, the display resistance value is not as common due to high resistance meter that measured voltage or current change of V I change, so, even if the measured voltage, resistance, power supply voltage is measured the changes in the results have little effect, the measurement accuracy is very high （ patent ）, theoretically the error can be zero, while the actual error can be done a few thousandths or extremely few.

Typical application

1 measurements of anti-static shoes, conductive shoes resistance value

2, measurement of the antistatic material resistance and resistivity

3, measurement computer room with movable floor system resistance

4, measurement of insulation resistance （ rate）

5, photodiode dark current measurement

6, physics, optics and materials research

Canton company other insulating materials testing instruments:

BDJC-0-100KV dielectric breakdown testing instrument

BDJC series insulating materials at power frequencies of dielectric breakdown test instrument

BDJC series voltage dielectric strength test apparatus

BDJC series voltage breakdown testing instrument

BDJC series insulating paint film breakdown strength tester

BDJC capacitor voltage breakdown testing instrument

EST-121 volume surface resistivity measuring instrument

GDAT-A dielectric loss tester / dielectric constant test

GDAT-C model dielectric constant dielectric loss tester

BDH leakage resistance tester

BDH-B arc resistance tester